Morco G11E Technical Information

10005246 03MORCO MODELS D-61B,D-61E AND G11E

10• DESCRIPTION AND OPERATION• These gas water heaters are equipped with:• A stainless steel burner which can operate with Butane/Propane-Natural.• A

11MORCO INSTANTANEOUSGAS WATER HEATERCE 0099Mod. Nº: G11E PROP99BP819Gas Type:G-30/G31 28-30mbarCat. I3+30mbar Cat. I3B/PG-30 37mbarType :B11BSQn (hi)

1- GAS SUPPLY CONNECTION3- GAS FILTER4- DRAIN PLUG5- LOWER PROTECTOR6- WATER FLOW REGULATOR7- WATER TEMP. SELECTOR8- INLET PRESSURE NIPPLE9- WATER FIL

A.2.2. - INSTALLATION INSTRUCTIONS• RECOMMENDATIONSFor the userThe appliance must be installed, adjusted or adapted for use with another type ofgas on

• COMBUSTION GAS REMOVALFlue: A draught diverter is fitted to the top of the water heater. The nominal fluesize is 90 mm. (D61B, D61E) and 110 mm. (G1

All permanent openings for ventilation should be designed to prevent the entry ofvermin. Where screens are provided, they should not have apertures of

• Ensure that all the washers are properly fitted.• Ensure all gas and water joints are sufficiently tight as not to leak.•WATER TIGHTNESS OF THE WATE

ø in mm.MODELSGAS TYPE BURNER PILOTD61B-D61E PROP/BUTANE 0,72 (6 off) 0,19D61B Natural 1,35 (6 off) 0,32G11E PROP/BUTANE 0,72 (12 off) 0,19G11E Natura

18• CLEANING THE HEAT EXCHANGERTo carry out the annual cleaning of the heating body, proceed as follows:- Turn off the gas supply- Turn off the supply

19PROBLEM CAUSE ACTIONNo spark. The piezo electric ignitor is faulty.Electrode is fractured. Electrode is dirty. Spark gap is too wide. Incorrect bat

PROBLEM CAUSE ACTIONMain Burner ignites when temp. adjusting knob is positioned at “HOT” but goes out when turned down to “WARM” position. Insufficie

21PROBLEM CAUSE ACTIONEven though temp. adjusting knob is turned to“HOT” Position, heated water is not hot enough due to too high a water flow rate.W

PROBLEM CAUSE ACTIONWater heater operates at taps but not at shower. Shower hose too small or kinked. Shower head restricted. High water pressure. Lo

INDEXA.- ENGLISHA.1. INSTRUCTIONS FOR USERS ... 5A.2. TECHNICAL INSTRUCTIONS FO

4MORCO MODELS D-61B, D61E AND G11EIMPORTANT INFORMATIONINSTANTANEOUS MULTI-POINT WATER HEATERFITTED WITH DRAUGHT DIVERTERFOR NORMAL OPEN FLUED SYSTEMT

A.1. - INSTRUCTIONS FOR USERSTechnical instructions for use and maintenanceWARNING: Before use, this appliance must be installed and adjusted by acomp

6• WATER TEMPERATURE SELECTIONTo adjust the hot water temperature, turn the selector control to the right for hotterwater and to the left for cooler w

• CHECKING FOR SAFE OPERATIONIn addition to any annual service by a competent person, the user should carry outthe following checks periodically and e

8A.2.- TECHNICAL INSTRUCTIONS FOR INSTALLATION ENGINEERSA.2.1. TECHNICAL INFORMATION• Shape and outer dimensionsLower of baseCWGASWWCWGASWWADCHJøEFBMC

• GAS CONSUMPTIONGAS PRESSURE ATTIPE OF GAS GAS FLOWAT 15ºC and 760 mm Hg APPLIANCE INLET(Standarised gases) (mbar)G11E D61B-D61EButane 1,8 kg/h. 0,88